- #Kodak esp office 2150 printhead carriage jam install
- #Kodak esp office 2150 printhead carriage jam upgrade
- #Kodak esp office 2150 printhead carriage jam full
- #Kodak esp office 2150 printhead carriage jam free
#Kodak esp office 2150 printhead carriage jam full
Please let me know if the issue is not solved so we can contiune troubleshooting.Printhead for Kodak ESP 2170 ESP 3.2 ESP C310 ESP C315 ESP C300 Description High quality and durable Fit perfectly for your machine Replacement For Kodak 30 Series Full color function. Pull on the clean out assembly to insure that it is sealed. Rotate the left side of the clean out assembly until the latch snaps into place. Insert the right side of the clean out assembly into the back of the printer so that the tabs fit into the slots on the right side of the clean out area. IMPORTANT: If the clean out assembly is not installed and seated correctly, paper jam or paper try empty errors may occur.Ī. If necessary, relocate the printer to a flat, hard surface. Check under the printer for obstructions. If necessary, carefully remove the foreign objects from your printer. If paper is not visible, check your printer for foreign objects, such as paper clips or staples. If necessary, slowly pull the jammed paper from your printer. Check the inside of your printer for a paper jam. *Carefully pivot the left side of the clean out assembly toward you to remove it.Ĥ. *Gently press and hold the tab on the left side of the clean out assembly. Remove the clean out assembly from the rear clean out area: If no luck, please follow the steps below from the REAR of the printer:ġ.
#Kodak esp office 2150 printhead carriage jam free
Make sure the paper output tray is open and free of any paper. Remove all paper from the paper input tray(s). Please test the machine and let me know the results.ġ. Once done, plug it back in and insert a single sheet of paper. If no luck still, remove all paper from the machine and then blow out the feed roller and paper tray thoroughly with compressed air three or four times. Then plug the printer back up, take your paper out and replace it with a fresh, small stack (about 5 pages) of paper. (Sometimes objects such as pens, paper clips, and so on can fall into the paper feed area and cause blockages.) Holding the printer in both hands (you may need another person to help you.), turn it upside down and shake it for a few seconds to see if anything falls out of the paper feed area. Dust may be coating the rollers there and as they become less tacky, they cannot feed paper correctly. Next, take a dry cloth or Q-tip and clean the rubber rollers in the automatic sheet feeder. If there is nothing obvious, un-plug the printer power supply. If no luck, please check using a flashlight, to ensure there is nothing obstructing the paper feed mechanism down inside the printer where it is not easily seen. Insert the color ink cartridge into the printhead, then press down firmly until you hear it click into position.ġ2. Insert the black ink cartridge into the printhead, then press down firmly until you hear it click into position.ġ1. Verify that the KODAK Ink Cartridges have not been refilled. Verify that the labels on the ink cartridges are intact, and that the cartridges are not damaged. Follow the instructions on the control panel LCD. Select "Install Ink Cartridges" and then press "OK".
#Kodak esp office 2150 printhead carriage jam upgrade
After you upgrade the firmware, press "Home" on the printer control panel.
#Kodak esp office 2150 printhead carriage jam install
Go to KODAK All-in-One Printer Downloads and Drivers, select your printer from the "All-in-One Printers" pull-down list, and download and install the latest firmware version for your printer. If an error is displayed on your printer control panel or the status monitor on your computer, press "Cancel" to clear the error.
If so, select "Install Ink Cartridges", press "OK", and follow the instructions. Check if the Install Ink Cartridge option is available. NOTE: If the printhead does not move to the center position, press "Home", then "Maintenance" on your printer.
Lift the printer access door, and then remove the ink cartridges from the printhead. Gently move printhead carriage from side to side to see that it moves freely and there are no obstructions.ġ.
Remove any paper, tape or other obstructions from the printhead carriage area. If you have any concerns or questions, please don't hesitate to ask. Hello, and thank you for using JustAnswer I will assist you in order to answer your question.
0 kommentar(er)
